The VF1 is an efficient filter suitable for roof areas of up to 500 m² . Water flows over a 2 stage stainless steel cascade, filtering to 0.55 mm. It is frost resistant and mostly self cleaning, requiring only minimal maintenance. The filter insert is easily removed for cleaning. In cases where leaves and other dirt cannot be discharged to waste the VF1 is available with a dirt retention basket fitted. An telescopic extension tube is also available to allow the VF1 to be installed up to 750 mm below ground level, this accessory is highly recommended for most installations.

• Connects to standard 110 mm drain
• For roof areas up to 500 square metres
• Dirt Retention Basket available
• Telescopic Extension available

The VF1 is an efficient filter suitable for roof areas of up to 500 square metres. Water flows over a 2 stage stainless steel cascade, filtering to 0.55 mm. It is frost resistant and mostly self cleaning, requiring only minimal maintenance. The filter insert is easily removed for cleaning. In cases where leaves and other dirt cannot be discharged to waste the VF1 is available with a dirt retention basket fitted. 

The supplied telescopic extension tube is also available to allow the VF1 to be installed up to 750 mm below ground level.

• Connects to standard 110 mm drain
• For roof areas up to 500 m² .
• Dirt Retention Basket available
• Telescopic Extension and Lid supplied

The VF1 is an efficient filter suitable for roof areas of up to 500 square metres. Water flows over a 2 stage stainless steel cascade, filtering to 0.55 mm. It is frost resistant and mostly self cleaning, requiring only minimal maintenance. The filter insert is easily removed for cleaning. In cases where leaves and other dirt cannot be discharged to waste the VF1 is available with a dirt retention basket fitted. An telescopic extension tube is also available to allow the VF1 to be installed up to 750 mm below ground level, this accessory is highly recommended for most installations.

• Connects to standard 110 mm drain
• For roof areas up to 500 m²
• Bottom Outlet
• Dirt Retention Basket available
• Telescopic Extension available

The VF1 is an efficient filter suitable for roof areas of up to 500 square metres. Water flows over a 2 stage stainless steel cascade, filtering to 0.55 mm. It is frost resistant and mostly self cleaning, requiring only minimal maintenance. The filter insert is easily removed for cleaning. In cases where leaves and other dirt cannot be discharged to waste the VF1 is available with a dirt retention basket fitted. An telescopic extension tube is also available to allow the VF1 to be installed up to 750 mm below ground level, this accessory is highly recommended for most installations.

• Connects to standard 110 mm drain
• For roof areas up to 500 square metres
• Bottom Outlet
• Dirt Retention Basket available
• Telescopic Extension available

Polyethylene lid with bayonet locking mechanism to fit VF1, GF and RF Filters.

The VF1 Dirt Retention Basket is for retro-fitting to VF1s, changing them into total retention filters.  This is ideal where no sewer connection is possible - all debris are held by the basket.

Complete with fixing screws. 

A filter insert for VF1 filters.  The filter insert gives two step filtration with its slats and fine, specially woven, steel mesh.

Simply push-fit into the VF1 filter housing.

An extension handle that can be attached to the filter insert of the VF1 to aid removal and cleaning where the filter is installed too deep for the filter insert to be conveniently reached.

The telescopic extension tube can be set to the desired height; from 250 - 750 mm from the filter inlet to the top of the extension tube.

Simple to use and install with a bayonet locking system.

Extension tubes can be attached together for extra height.

Please Note: The extension tube does NOT include lid, this must be purchased separately.

Connection inlet: DN 200
Outlet into the tank: DN 150
Outlet into the sewer: DN 200

Height difference between inlet and outlet 320 mm.

Material Filter corpus: Stainless steel

Material Filter sieve: Stainless steel

Mesh size: 0.4 x 1 mm

Legs = Thread rods M10 with screw nut made of stainless steel

Length 250 mm

Weight: 24.2 kg